Civil infrastructure systems are generally the most expensive assets in any country, and these systems are deteriorating at an alarming rate. In addition, these systems have a long service life in comparison to most other commercial products. As well, the introduction of intelligent materials and innovative design approaches in these systems is painfully slow due to heavy relianceon traditional construction and maintenance practices, and the conservative nature of design codes. Feedback on the "state of the health" of constructed systems is practically nonexistent. In the quest for lighter, stronger and corrosion-resistant structures, the replacement of ferrous materials by high-strength fibrous ones is being actively pursued in several countries around the world, both with respect to the design of new structures as well as for the rehabilitation and strengthening of existing ones. In North America, active research in the design of new highway bridges is focused on a number of specialty areas, including the replacement of steel reinforcing bars in concrete deck slabs by randomly distributed low-modulus fibers, and the replacement of steel prestressing cables for concrete components by tendons comprising super-strong fibers. Research is also being conducted on using FRPs to repair and strengthen existing structures.

Structural health monitoring (SHM) uses one or more in situ sensing systems placed in or around a structure, providing real-time evaluation of its performance and ultimately preventing structural failure. Although most commonly used in civil engineering, such as in roads, bridges, and dams, SHM is now finding applications in other engineering envir

This research report discusses the planning necessary for the proper development, acquisition, installation, and maintenance of an effective health monitoring network for transportation infrastructure systems. A comprehensive literature search was conducted, and the materials were compiled into a database, reviewed, and synthesized. Data elements vital for maintaining safe and functional transportation infrastructures were identified and discussed for bridge structures, pavements, and geotechnical structures. Moreover, the steps necessary for planning an instrumentation system for a particular structure are presented. Sample design plans for the transportation infrastructure systems that are typically constructed in Wisconsin were obtained from WisDOT, and suggested instrumentation plans were developed for these transportation systems. One of the objectives of the research project is to identify urban freeway construction projects that could efficiently serve as hosts for an infrastructure health monitoring (IHM) instrumentation testbed. Major current and near-future construction projects in Wisconsin were identified and critically evaluated to identify a candidate project to host the IHM testbed. Among the candidates, the Zoo Interchange reconstruction project is recommended for hosting the infrastructure health monitoring testbed. Cost estimates based on current market prices are provided for the instrumentation plans developed for IHM of bridge structures, pavements, and geotechnical structures. To provide an example of using IHM data in applications, archived data from the Marquette Interchange instrumentation project was used to develop vehicle wander patterns and load spectra data, both in the form needed to conduct a mechanistic appraisal of the pavement structure using the DARWin ME software. The research team designed and conducted an IHM survey of state highway agencies in the U.S. and Canada. The survey showed that 46 percent of state DOTs have implemented health monitoring applications for transportation infrastructure. The survey also identified the impediments facing state DOTs in implementing IHM systems.

Wireless MEMS Networks and Applications reviews key emerging applications of MEMS in wireless and mobile networks. This book covers the different types of wireless MEMS devices, also exploring MEMS in smartphones, tablets, and the MEMS used for energy harvesting. The book reviews the range of applications of wireless MEMS networks in manufacturing, infrastructure monitoring, environmental monitoring, space applications, agricultural monitoring for food safety, health applications, and systems for smart cities. - Focuses on the use of MEMS in the emerging area of wireless applications - Contains comprehensive coverage of the range of applications of MEMS for wireless networks - Presents an international range of expert contributors who identify key research in the field

This paper outlines a 5-year research plan for the development of a structural health monitoring system for timber bridges. A series of studies identify and evaluate various sensing technologies for measurement of structural adequacy and/or deterioration parameters. The overall goal is to develop a turn-key system to analyze, monitor, and report on the performance and condition of timber bridges. The introduction of structural health monitoring technologies for timber bridges should result in improved safety, longer service life, and improved load ratings.

Concrete structures have been built for more than 100 years. At first, reinforced concrete was used for buildings and bridges, even for those with large spans. Lack of methods for structural analysis led to conservative and reliable design. Application of prestressed concrete started in the 40s and strongly developed in the 60s. The spans of bridges and other structures like halls, industrial structures, stands, etc. grew significantly larger. At that time, the knowledge of material behaviour, durability and overall structural performance was substantially less developed than it is today. In many countries statically determined systems with a fragile behavior were designed for cast in situ as well as precast structures. Lack of redundancy resulted in a low level of robustness in structural systems. In addition, the technical level of individual technologies (e.g. grouting of prestressed cables) was lower than it is today. The number of concrete structures, including prestressed ones, is extremely high. Over time and with increased loading, the necessity of maintaining safety and performance parameters is impossible without careful maintenance, smaller interventions, strengthening and even larger reconstructions. Although some claim that unsatisfactory structures should be replaced by new ones, it is often impossible, as authorities, in general, have only limited resources. Most structures have to remain in service, probably even longer than initially expected. In order to keep the existing concrete structures in an acceptable condition, the development of methods for monitoring, inspection and assessment, structural identification, nonlinear analysis, life cycle evaluation and safety and prediction of the future behaviour, etc. is necessary. The scatter of individual input parameters must be considered as a whole. This requires probabilistic approaches to individual partial problems and to the overall analysis. The members of the fib Task Group 2.8 “Safety and performance concepts” wrote, on the basis of the actual knowledge and experience, a comprehensive document that provides crucial knowledge for existing structures, which is also applicable to new structures. This guide to good practice is divided into 10 basic chapters dealing with individual issues that are critical for activities associated with preferably existing concrete structures. Bulletin 86 starts with the specification of the performance-based requirements during the entire lifecycle. The risk issues are described in chapter two. An extensive part is devoted to structural reliability, including practical engineering approaches and reliability assessment of existing structures. Safety concepts for design consider the lifetime of structures and summarise safety formats from simple partial safety factors to develop approaches suitable for application in sophisticated, probabilistic, non-linear analyses. Testing for design and the determination of design values from the tests is an extremely important issue. This is especially true for the evaluation of existing structures. Inspection and monitoring of existing structures are essential for maintenance, for the prediction of remaining service life and for the planning of interventions. Chapter nine presents probabilistically-based models for material degradation processes. Finally, case studies are presented in chapter ten. The results of the concrete structures monitoring as well as their application for assessment and prediction of their future behaviour are shown. The risk analysis of highway bridges was based on extensive monitoring and numerical evaluation programs. Case studies perfectly illustrate the application of the methods presented in the Bulletin. The information provided in this guide is very useful for practitioners and scientists. It provides the reader with general procedures, from the specification of requirements, monitoring, assessment to the prediction of the structures’ lifecycles. However, one must have a sufficiently large amount of experimental and other data (e.g. construction experience) in order to use these methods correctly. This data finally allows for a statistical evaluation. As it is shown in case studies, extensive monitoring programs are necessary. The publication of this guide and other documents developed within the fib will hopefully help convince the authorities responsible for safe and fluent traffic on bridges and other structures that the costs spent in monitoring are first rather small, and second, they will repay in the form of a serious assessment providing necessary information for decision about maintenance and future of important structures.

Integrative Oncology explores a comprehensive, evidence-based approach to cancer care that addresses all individuals involved in the process, and can include the use of complementary and alternative medicine (CAM) therapies alongside conventional modalities such as chemotherapy, surgery, and radiation therapy. The number of integrative care programs is increasing worldwide and this book forms a foundation text for all who want to learn more about this growing field. This guide provides a thoughtful and generous perspective on integrative care, an outstanding overview of the exciting clinical opportunities these techniques can offer, and a guide to the new territories that all oncologists and CAM practitioners need to explore and understand.

This eBook is a collection of articles from a Frontiers Research Topic. Frontiers Research Topics are very popular trademarks of the Frontiers Journals Series: they are collections of at least ten articles, all centered on a particular subject. With their unique mix of varied contributions from Original Research to Review Articles, Frontiers Research Topics unify the most influential researchers, the latest key findings and historical advances in a hot research area! Find out more on how to host your own Frontiers Research Topic or contribute to one as an author by contacting the Frontiers Editorial Office: frontiersin.org/about/contact.